Pallet Labels, Barcodes and Hand Stretch Film

Keep pallet labels readable and scannable when hand stretch film is applied for Australian warehousing and distribution.

Pallet Labels, Barcodes and Hand Stretch Film article image

A stable pallet can still miss a despatch window if the receiver cannot scan it. Wrinkled labels, excessive glare, film folds and labels hidden under later revolutions create avoidable work at staging and receiving.

The wrapping and labelling sequence should be designed together. The goal is not merely to see a barcode through clear hand stretch film; it is to produce the correct logistic unit identification in the location and condition required by the trading partner.

Decide which label identifies the logistic unit

Carton GTIN labels and a pallet SSCC serve different purposes. For GS1 logistic labels, the SSCC is the mandatory identifier for the logistic unit. Mixed pallets normally rely on the SSCC and electronic data rather than trying to describe every carton in a pallet barcode.

Confirm customer, carrier and warehouse-management requirements before printing. Do not create a second identification scheme just to work around a wrapping problem.

Apply the logistic label outside the completed wrap

For a GS1 logistic label, the practical default is a clear, unobscured label applied to the outside of the completed wrap. Choose label stock and adhesive that remain secure on the film through normal staging, transport and receipt.

A label beneath clear film may be protected from dirt, but multiple layers, wrinkles, moisture and reflections can interfere with scanning. Treat under-film placement only as a trading-partner-approved, scan-verified exception. For joined stacked pallets shipped as one logistic unit, GS1 calls for the master SSCC label to be applied outside the wrapping.

Follow the applicable placement rules

GS1’s logistic-label guideline places pallet barcodes between 400 mm and 800 mm from the pallet base, at least 50 mm from a vertical edge. For a pallet less than 400 mm high, the barcode is placed as high as possible while keeping it protected. The guideline also recommends identical labels on two sides so one remains accessible. See the GS1 Logistic Label Guideline.

These rules apply to GS1 logistic labels; customer-specific labels may have additional instructions. Make sure the final wrapped unit—not only the unwrapped stack—meets the requirement.

Prevent common wrapping defects

Keep the label zone away from film tails and heavy folded seams. If the label is applied before wrapping, avoid placing a roped film band through the barcode. If it is applied afterwards, smooth the film surface without cutting or weakening the containment layers.

Do not cut a window into the wrap after the pallet is complete. That can reduce containment and create a tear path.

Test scanners in real conditions

Scan the finished pallet from the normal aisle position with the devices used at despatch and receipt. Include:

  • bright dock light and normal warehouse light;
  • labels on adjacent sides;
  • the shortest and tallest validated pallets;
  • chilled or humid conditions where relevant;
  • pallets after normal staging, not only immediately after wrapping.

GS1 Australia’s barcode checklist specifically warns against shrink-wrap, tape or printing obscuring the finished barcode. See its barcode generation checklist.

Record no-reads and rescans, not just a final successful scan. A barcode that works after five attempts is still an operational problem.

Write the sequence into the work instruction

State when the label prints, who confirms the pallet identity, where labels are applied, whether they sit above or below film, and when the final scan occurs. Require the operator to match the SSCC with the despatch record before loading.

For combined or stacked pallet units, obtain system guidance on parent or master identification rather than leaving several visible labels to compete at receiving.

FAQ

Can scanners read through clear stretch film?

Sometimes, but folds, glare, moisture, tension and label quality can cause failures. Validate the finished unit with the real scanners.

Should labels be placed on two sides?

GS1 recommends two identical logistic labels on adjacent pallet sides. Follow the applicable standard and trading-partner requirements.

Can we tape a failed label over the film?

Only if the label remains correct, secure and compliant with the receiving requirement. Investigate the underlying placement or material problem.

Include label performance when trialling manual pallet wrap, not as a separate check after procurement is complete.

Tags

Related Articles

© 2026 Cline Plus, Powered by Shopify

    • American Express
    • Apple Pay
    • Google Pay
    • Mastercard
    • PayPal
    • Shop Pay
    • Union Pay
    • Visa

    Login

    Forgot your password?

    Don't have an account yet?
    Create account